TnT Landing Gear Products is now offering SWB products

SWB DOUBLE-LOC SERVO ARMS

JR,HITEC,FUTABA

JR 1" Half Arm

Hitec 1" Half Arm

Futaba 1" Half Arm

$9.50

SWB 1'' Half Arm:

JR 1-1/4" Half Arm

Hitec 1-1/4" Half Arm

Futaba 1-1/4" Half Arm

$10.00

SWB 1-1/4 Half Arm:

JR 1-1/2" Half Arm

Hitec 1-1/2" Half Arm

Futaba 1-1/2" Half Arm

$12.00

SWB 1-1/2 Half Arm:

JR 2" Half Arm

Hitec 2" Half Arm

Futaba 2" Half Arm

$13.00

2:

JR 1-1/4" Full Arm

Hitec 1-1/4" Full Arm

Futaba 1-1/4" Full Arm

$11.00

SWB1-1/4:

JR 1-1/2" Full Arm

Hitec 1-1/2" Full Arm

Futaba 1-1/2" Full Arm

$14.00

SWB 1-1/2 Full Arm:

JR 2-1/4" Full Arm

Hitec 2-1/4" Full Arm

$20.00

SWB 2-1/4:

JR 3" Offset Full Arm

Hitec 3" Offset Full Arm

Futaba 3" Offset Full Arm

$18.00

SWB 3:

JR 4" Offset Full Arm

Hitec 4" Offset Full Arm

$20.00

SWB 4:

Titanium Turnbuckles NEW

3/16 Hex with 4/40 RH & LH Thread
5/8" long thread each side
2 turnbuckles per package

Titanium 1-1/2" Turnbuckle

$6.00 per package

Titanium 2" Turnbuckle

$7.00 per package

Titanium 2-1/2" Turnbuckle

$8.00 per package

Titanium 3" Turnbuckle

$9.00 per package

Titanium 3-1/2" Turnbuckle

$10.00 per package

Titanium 4" Turnbuckle

$11.00 per package

Titanium 4-1/2" Turnbuckle

$12.00 per package

Pull-Pull Wire Tensioners

This kits includes 2) 1- 1/2 titanium turnbuckles, 2) RH #87 Ball links and 2) wire adapters. Connect up to your bellcrank and you have up to a 1/2" of adjustment. These wire adapters provide a nice round connection for your wire rope, so there is no kinking. Works great with Kevlar! Installation instructions included.

$18.00 pr.

Motor Mounts for 100cc ,120-150 cc &3W-157

120-150cc Aluminum Motor Mount 0°

This specially designed aluminum mount for DA or 3W 120cc-150cc motors used on models that have the right thrust built in and weighs less than 2 oz. These will save you a lot of time and effort. Machined from 6061-T6 with a 5/8 rise at the highest point . Just draw your horizontal and vertical center lines, then line up the cross hairs on the mount. There even is 4)- #4 holes so you can mount it to your firewall and use it as a drill fixture. 4)-1/4",4)-1/8" & 4)-1/16" boss extensions included.

$60.00

120-150cc Aluminum Motor Mount 2-1/2 °

This specially designed aluminum mount for DA or 3W 120cc-150cc motors and weight less than 2 oz. These will save you a lot of time and effort. Machined from 6061-T6 with a 5/8 rise at the highest point and 2-1/2° machined right into the mount. Just draw your horizontal and vertical center lines, then draw your offset vertical line (11/32 typical left side of plane) line up the cross hairs on the mount. There even is 4)- #4 holes so you can mount it to your firewall and use it as a drill fixture. 4)-1/4",4)-1/8" & 4)-1/16" boss extensions included.

$60.00

120-150cc Aluminum Motor Mount 3 °

This specially designed aluminum mount for DA or 3W 120cc-150cc motors and weight less than 2 oz. These will save you a lot of time and effort. Machined from 6061-T6 with a 5/8 rise at the highest point and 3° machined right into the mount. Just draw your horizontal and vertical center lines, then draw your offset vertical line (7/16" typical left side of plane) line up the cross hairs on the mount. There even is 4)- #4 holes so you can mount it to your firewall and use it as a drill fixture. 4)-1/4",4)-1/8" & 4)-1/16" boss extensions included.

$60.00

120-150cc Aluminum Motor Mount 3 1/2°

This specially designed aluminum mount for DA or 3W 120cc-150cc motors and weight less than 2 oz. These will save you a lot of time and effort. Machined from 6061-T6 with a 5/8 rise at the highest point and 3-1/2° machined right into the mount. Just draw your horizontal and vertical center lines, then draw your offset vertical line (1/2 typical left side of plane) line up the cross hairs on the mount. There even is 4)- #4 holes so you can mount it to your firewall and use it as a drill fixture. 4)-1/4",4)-1/8" & 4)-1/16" boss extensions included.

$60.00

3W 157cc Aluminum Motor Mount 0°

This specially designed aluminum mount for 3W 157cc motors used on models that have the right thrust built in and weighs less than 2 oz. These will save you a lot of time and effort. Machined from 6061-T6 with a 5/8 rise at the highest point . Just draw your horizontal and vertical center lines, then line up the cross hairs on the mount. There even is 4)- #4 holes so you can mount it to your firewall and use it as a drill fixture. 4)-1/4",4)-1/8" & 4)-1/16" boss extensions included.

$60.00

3W 157cc Aluminum Motor Mount 2-1/2°

This specially designed aluminum mount for 3W 157cc motors and weight less than 2 oz. These will save you a lot of time and effort. Machined from 6061-T6 with a 5/8 rise at the highest point and 2-1/2° machined right into the mount. Just draw your horizontal and vertical center lines, then draw your offset vertical line (5/16 typical left side of plane) line up the cross hairs on the mount. There even is 4)- #4 holes so you can mount it to your firewall and use it as a drill fixture. 4)-1/4",4)-1/8" & 4)-1/16" boss extensions included.

$60.00

3W 157cc Aluminum Motor Mount 3°

This specially designed aluminum mount for 3W 157cc motors and weight less than 2 oz. These will save you a lot of time and effort. Machined from 6061-T6 with a 5/8 rise at the highest point and 3° machined right into the mount. Just draw your horizontal and vertical center lines, then draw your offset vertical line (5/16 typical left side of plane) line up the cross hairs on the mount. There even is 4)- #4 holes so you can mount it to your firewall and use it as a drill fixture. 4)-1/4",4)-1/8" & 4)-1/16" boss extensions included.

$60.00

3W 157cc Aluminum Motor Mount 3-1/2°

This specially designed aluminum mount for 3W 157cc motors and weight less than 2 oz. These will save you a lot of time and effort. Machined from 6061-T6 with a 5/8 rise at the highest point and 3-1/2° machined right into the mount. Just draw your horizontal and vertical center lines, then draw your offset vertical line (5/16 typical left side of plane) line up the cross hairs on the mount. There even is 4)- #4 holes so you can mount it to your firewall and use it as a drill fixture. 4)-1/4",4)-1/8" & 4)-1/16" boss extensions included.

$60.00

100cc Aluminum Motor Mount 2-1/2°

This specially designed aluminum mount for DA or 3W 100cc motors and weight less than 2 oz. These will save you a lot of time and effort. Machined from 6061-T6 with a 3/8 rise at the highest point and 2-1/2° machined right into the mount. Just draw your horizontal and vertical center lines, then draw your offset vertical line (5/16 typical left side of plane) line up the cross hairs on the mount. There even is 4)- #4 holes so you can mount it to your firewall and use it as a drill fixture. 4)-1/4",4)-1/8" & 4)-1/16" boss extensions included.

$55.00

Motor Stand Offs

**For Use on Aircraft that have the right thrust built in **

**ALL STAND OFFS HAVE A 1/4" THROUGH HOLE**

1/2"-15/16" Motor Stand Offs

Why goof around with using steel washers that are not all the same thickness. Here is a quick an simple way of spacing out your motor. The base stand off is precision machined from 6061-T6 aluminum. It measures 1" diameter at the base to give a good load bearing on the wood, and necks down to 5/8" in diameter at the motor and is a 1/2" long. If more length is required, simply add the spacers included to get the desired length up to 15/16" long. Kit comes complete with (4ea.of the following) 1/2" bases, 1/4", 1/8" & 1/16"

$22.00

1"-1-7/16" Motor Stand Offs

Why goof around with using steel washers that are not all the same thickness. Here is a quick an simple way of spacing out your motor. The base stand off is precision machined from 6061-T6 aluminum. It measures 1" diameter at the base to give a good load bearing on the wood, and necks down to 5/8" in diameter at the motor and is a 1" long. If more length is required, simply add the spacers included to get the desired length up to 1-7/16" long. Kit comes complete with (4ea.of the following) 1" bases, 1/4", 1/8" & 1/16"

$24.00

1-1/2" to 1-15/16" Motor Stand Offs

Why goof around with using steel washers that are not all the same thickness. Here is a quick an simple way of spacing out your motor. The base stand off is precision machined from 6061-T6 aluminum. It measures 1" diameter at the base to give a good load bearing on the wood, and necks down to 5/8" in diameter at the motor and is a 1-1/2" long. If more length is required, simply add the spacers included to get the desired length up to 1-15/16" long. Kit comes complete with (4ea.of the following) 1-1/2" bases, 1/4", 1/8" & 1/16"

$26.00

2" to 2-7/16" Motor Stand Offs

Why goof around with using steel washers that are not all the same thickness. Here is a quick an simple way of spacing out your motor. The base stand off is precision machined from 6061-T6 aluminum. It measures 1" diameter at the base to give a good load bearing on the wood, and necks down to 5/8" in diameter at the motor and is a 2" long. If more length is required, simply add the spacers included to get the desired length up to 2-7/16" long. Kit comes complete with (4ea.of the following) 2" bases, 1/4", 1/8" & 1/16"

$28.00

Rudder Horns

Rudder Horns RH4.00X.75

These horns are the popular style than go through the rudder, made of 2024-t3 aluminum and are machined to match common sizes. The RH 4.00 X.75 are 4" hole to hole and to be used with a 3/4" or less bevel.

$18.00

Rudder Horns RH4.50X.75

These horns are the popular style than go through the rudder, made of 2024-t3 aluminum and are machined to match common sizes. The RH 4.50 X.75 are 4-1/2" hole to hole and to be used with a 3/4" or less bevel.

$20.00

Rudder Horns RH4.50X 1.0

These horns are the popular style than go through the rudder, made of 2024-t3 aluminum and are machined to match common sizes. The RH 4.50 X 1.0 are 4-1/2" hole to hole and to be used with a 1" or less bevel.

$20.00

Rudder Horns RH5.0X.75

These horns are the popular style than go through the rudder, made of 2024-t3 aluminum and are machined to match common sizes. The RH 5.0 X.75 are 5"; hole to hole and to be used with a 3/4" or less bevel.

$22.00

Stand Alone Bellcranks

** Bellcranks below are designed to use the 1" or 1-1/4" full arm.**

4" Straight Bellcrank

Take a load off your standard size servo or servo's with this straight bellcrank it is designed to be used with a 3, 3-1/2 or 4" rudder horn mounted on Hinge line and running the wires straight. The height of the assembly will match most brand names standard size servo's. It comes complete with and isolated delrin bearing, pivot and SS mounting screw. Hole spacing is 1/4" and tapped for 4/40. This Bellcrank is designed to be used with 1" or 1-1/4" Full Arms.

$24.00

5" Straight Bellcrank

Take a load off your standard size servo or servo's with this straight bellcrank it is designed to be used with a 3, 3-1/2, 4, 4-1/2 or 5" rudder horn mounted on Hinge line and running the wires straight. The height of the assembly will match most brand names standard size servo's. It comes complete with and isolated delrin bearing, pivot and SS mounting screw. Hole spacing is 1/4" and tapped for 4/40.. This Bellcrank is designed to be used with 1" or 1-1/4" Full Arms.

$25.00

4"Offset Bellcrank

Take a load off your standard size servo or servo's with this Offset bellcrank. This bellcrank design is to be used with a 4" rudder horn mounted on Hinge line and crossing the wires. The height of the assembly will match most brand names standard size servo's. It comes complete with and isolated delrin bearing, pivot and SS mounting screw. Hole spacing is 1/4" and tapped for 4/40. This Bellcrank is designed to be used with 1" or 1-1/4" Full Arms. Note this bellcrank does not measure 4"

$25.00

4-1/4"Offset Bellcrank

Take a load off your standard size servo or servo's with this Offset bellcrank. This bellcrank design is to be used with 2.6M COMP ARF's crossing the wires. The height of the assembly will match most brand names standard size servo's. It comes complete with and isolated delrin bearing, pivot and SS mounting screw. Hole spacing is 1/4" and tapped for 4/40. This Bellcrank is designed to be used with 1" or 1-1/4" Full Arms. Note this bellcrank does not measure 4-1/4"

$25.50

4-1/2"Offset Bellcrank

Take a load off your standard size servo or servo's with this Offset bellcrank. This bellcrank design is to be used with a 4-1/2" rudder horn mounted on Hinge line and crossing the wires. The height of the assembly will match most brand names standard size servo's. It comes complete with and isolated delrin bearing, pivot and SS mounting screw. Hole spacing is 1/4" and tapped for 4/40. This Bellcrank is designed to be used with 1" or 1-1/4" Full Arms. Note this bellcrank does not measure 4-1/2"

$26.00

5"Offset Bellcrank

Take a load off your standard size servo or servo's with this Offset bellcrank. This bellcrank design is to be used with a 5" rudder horn mounted on Hinge line and crossing the wires. The height of the assembly will match most brand names standard size servo's. It comes complete with and isolated delrin bearing, pivot and SS mounting screw. Hole spacing is 1/4" and tapped for 4/40. This Bellcrank is designed to be used with 1" or 1-1/4" Full Arms. Note this bellcrank does not measure 5" (COMP ARF'S 3.3 YAK 3.0 EXTRA260)

$27.00

Rudder - Servo Tray Kits

Made for specific aircraft with everything you need to install your rudder system!

Kits available for Carden's 35 & 40% Cap 232,Edge 540 & Extra 330

Just to name a few

Made in U.S.A.

1X Tray W/ 4" Offset Bellcrank Kit for JR

This tray is designed for models that only require 1 of the new high torque servo's that have a 4" rudder horn and crossing the wires. The kit comes complete as shown plus 10' of pull-pull wire. (Servo not included)
$90.00

1X Tray W/ 4-1/4" Offset Bellcrank Kit for JR
This tray is designed for models (Like the 2.6 Comp ARF) that only require 1 of the new high torque servo's that have a 4-1/4" rudder horn and crossing the wires. The kit comes complete as shown plus 10' of pull-pull wire. (Servo not included)

$90.00

1X Tray W/ 4" Offset Bellcrank Kit for HITEC

1X Tray W/ 4-1/4" Offset Bellcrank Kit for HITEC
This tray is designed for models (Like the 2.6 Comp ARF) that only require 1 of the new high torque servo's that have a 4-1/4" rudder horn and crossing the wires. The kit comes complete as shown plus 10' of pull-pull wire. (Servo not included)
$90.00

1X Tray W/ 4" Offset Bellcrank Kit for Standard FUTABA
This tray is designed for models that only require 1 of the new high torque servo's that have a 4" rudder horn and crossing the wires. The kit comes complete as shown plus 10' of pull-pull wire. (Servo not included)
$90.00

1X Tray W/ 4-1/4" Offset Bellcrank Kit for Standard FUTABA
This tray is designed for models (Like the 2.6 Comp ARF) that only require 1 of the new high torque servo's that have a 4-1/4" rudder horn and crossing the wires. The kit comes complete as shown plus 10' of pull-pull wire. (Servo not included)
$90.00

Hardware Kits for Servo Trays

2XHKBC Hardware kit for ST2X4BC Aluminum Servo Tray W/ Bellcrank>This hardware kits includes 4) 1- 1/2 titanium turnbuckles, 6) RH #87 Ball links, 4) LH #87 Ball Links plus all the mounting hardware to finish mount your servo's and arms in the tray. Installation instruction included.

$33.00

3XHKBC Hardware kit for ST3X5BC Aluminum Servo Tray W/ Bellcrank

This hardware kits includes 6) 1- 1/2 titanium turnbuckles, 8) RH #87 Ball links, 6) LH #87 Ball Links plus all the mounting hardware to finish mount your servo's and arms in the tray. Installation instruction included.

$46.00

4XHKBC Hardware kit for ST4X5BC Aluminum Servo Tray W/ Bellcrank

This hardware kits includes 8) 1- 1/2 titanium turnbuckles, 10) RH #87 Ball links, 8) LH #87 Ball Links plus all the mounting hardware to finish mount your servo's and arms in the tray. Installation instruction included.

$59.00

Professional Fuel Tank Caps

Aluminum Fuel Tank Cap

Anodized Aluminum Fuel Tank Cap for 5/32" fuel tubing designed to fit most fuel tanks. Heavy duty aluminum cap and base with a stainless socket head screw for a positive fit.

$9.00

Professional Servo Trays

** Servo trays below are designed to use the 1" or 1-1/4" full arm.**

ST2X4BC Aluminum Servo Tray With Bellcrank

Anodized Aluminum Servo Tray with 4" bellcrank designed to gang two servos on rudder pull pull systems. Servo tray fits Futaba and JR servos, sized for 1 1/2 titanium links, servo mounting holes tapped for 2-56 screws, isolated 4 inch bellcrank with .25 inch spaced holes, capable of 50+ degrees of throw. The Weight is only 2.6 oz. This tray is designed for 1" or 1-1/4" Full Arms.

$65.00

ST3X5BC Aluminum Servo Tray With Bellcrank

Anodized Aluminum Servo Tray with 5" bellcrank designed to gang three servos on rudder pull pull systems. Servo tray fits Futaba and JR servos, sized for 1 1/2 titanium links, servo mounting holes tapped for 2-56 screws, isolated 5 inch bellcrank with .25 inch spaced holes, capable of 50+ degrees of throw. The Weight is only 3.2 oz. This tray is designed for 1" or 1-1/4" Full Arms.

$71.00

ST4X5BC Aluminum Servo Tray With Bellcrank

Anodized Aluminum Servo Tray with 5"bellcrank designed to gang four servos on rudder pull pull systems. Servo tray fits Futaba and JR servos, sized for 1 1/2 titanium links, servo mounting holes tapped for 2-56 screws, isolated 5 inch bellcrank with .25 inch spaced holes, capable of 50+ degrees of throw. The Weight is only 3.8 oz. This tray is designed for 1" or 1-1/4" Full Arms.

$81.00

SWB MFG, INC. New Self adjusting Servo trays

Self Adjusting Bellcrank

NO MATCHBOX OR COMPLEX MIXING NEEDED!!!

SWB's new self adjusting servo's trays are not only compact but will never bind while still loading each servo 100% equally. Unlike matching servo's electronically, this system self adjusts across the complete travel of the servo, not just at neutral and full deflection!!! In fact you can have a servo completely lock up in a full deflection and the bellcrank can still be able to get back to center, a great safety feature. This system is available for standard size servo's as well as the popular 1/4 scale size.

Due to the many combinations of servo tray, bellcrank and servo manufacture's I will only be taking phone orders. These kits will include the following.
1-Servo tray w/your choice of bellcrank.
(4",5"straight/4",4-1/4"or4-1/2"offset bellcrank) 4-1/4" is for 2.6m Comp-ARF

1-Self adjusting hardware kit (everything you need to mount your servo's and connect the bellcrank).
1-1/4 Full servo arms (quantity needed)
1- Pair Wire Tensioners (For Rudder)
10' #90 Nylon Coated Wire (For Rudder)
DETAILED INSTRUCTIONS!!!

2X Standard Self adjusting servo kit $140.00 ea.

2X 1/4 Scale Self adjusting servo Kit $145.00ea.

3X Standard Self adjusting servo kit $225.00 ea.

4X Standard Self adjusting servo kit $270.00 ea.

Due to pre introduction popularity Self adjusting hardware NOT sold separately

Please call us to order this item Thank you 419-868-5408